Printronix SL4M MP2 Especificaciones Pagina 201
- Pagina / 308
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Fault Messages
201
ERROR: INSUFFICIENT
DRAM
Cycle Power
Yes/No Not enough RAM
memory available for a
printer function.
1. Power off the printer for
15 seconds, then power
back on again.
2. If the message
reappears, delete files
from FFS as they are
copied into RAM.
3. Select the menu option,
Optimize & Reboot.
4. If the message
reappears, replace the
controller PCBA. Write
down the message and
return it with the
defective board.
ERROR: INSUFFICIENT
FLASH
Cycle Power
Yes The printer requires
more flash memory to
run the downloaded
program.
1. Power off the printer for
15 seconds, then power
back on. If the problem
persists, contact your
authorized customer
service representative.
2. Consider installing an
optional Expanded
Memory Cartridge
(EMC) that adds 32 MB
of Flash memory to the
printer.
ERROR OCCURRED:
CLEARING QUEUES
Please Wait
Yes An interim message
displays while the
printer discards host
data it cannot use
because a fault
condition exists. While
this message displays,
the asterisk (*) rotates.
Wait. When the asterisk (*)
stops rotating, a different
fault message will appear;
troubleshoot the final
message.
ERROR: PROGRAM
NEEDS MORE DRAM
Yes/No The program exceeds
the memory limitations
of the printer.
Download a smaller
program.
Table 15. Fault Messages
Displayed Message
Can User
Correct?
Explanation Solution
- Administrator’s Manual 1
- SL4M™ and T4M™ 1
- Trademark Acknowledgements 3
- Table of Contents 10
- 1 Introduction 11
- Optional Features 12
- Thermal Printer Technology 14
- Manual Conventions 14
- Related Documents 15
- Thermal Consumables 16
- 2 Operation 17
- Installation 18
- Chapter 2 Installation 20
- Setting Up the Printer 21
- Loading Ribbon 22
- Loading Roll Media 25
- Media Roll 26
- Media Hanger 26
- Side Wall 26
- Media Sensor Assembly 28
- Inside Media 28
- Edge Guide 28
- (left edge) 28
- Loading Fanfold Media 30
- Operating Modes 34
- Controls and Indicators 35
- Control Panel 36
- Down Key 38
- Right Key 38
- Media Handling Modes 40
- Printhead Pressure Adjustment 41
- Media Width Adjustment 42
- Printhead Alignment 43
- Positioning the Media Sensors 44
- Sensing Different Media Types 46
- Running Auto Calibrate 47
- Running Media Profile 48
- Í Label Feed Direction 49
- Running Manual Calibrate 50
- Chapter 2 52
- 3 Standard Interfaces 53
- Parallel Interface 54
- Centronics Interface Signals 55
- Compatibility Mode 56
- Nibble Mode 56
- Byte Mode 56
- IEEE 1284 Interface Signals 57
- Chapter 3 Parallel Interface 58
- Serial Interface 59
- Chapter 3 Serial Interface 60
- 4 Configuring the Printer 61
- ↵ THE ↵ KEY IS 62
- Selecting a Menu Option 63
- Hidden Menus 64
- Menu Overview 65
- Main Menu 66
- Refer to the RFID 67
- Labeling Reference 67
- MEDIA SETUP Menu 68
- Print Intensity 69
- Print Speed 69
- Print Mode 69
- Media Handling 69
- Adv Continuous 70
- Tear Off Adjust 71
- Label Length 71
- Label Width 72
- Ver Image Shift 72
- Hor Image Shift 72
- "(+) A (-)i 72
- Orientation 73
- Chapter 4 MEDIA SETUP Menu 74
- Auto Map Select 75
- Auto Label Width 77
- Num Auto Labels 78
- Slew Speed Ctrl 78
- Print Direction 78
- Label Wait Time 79
- Label Missing 79
- Clip Page 80
- Fault Reprint 81
- Ribbon Low 81
- Set Label Length 81
- TOF Detect Fault 82
- Ticket Save Mode 82
- TOF Adjust Mode 83
- TOF Adjust 83
- BackFeed Motion 83
- SENSOR SETUP Menu 84
- Gap/Mark Sensor 85
- Run Auto-Cal (Auto-Calibrate) 85
- Run Profile 86
- Sensed Distance 86
- Gap/Mark Thresh 86
- Paper Out Thresh 86
- Run Manual Cal 87
- Pwr Up Action 87
- Head Auto-Cal 88
- Online Auto-Cal 88
- Gap Windowing 88
- Gap Length 89
- Cal in Peel Mode 89
- Min Calib Delta 89
- Use Label Length 90
- Threshold Range 90
- Mark TOF Detect 91
- Chapter 4 EMULATION MENU 92
- Overview 93
- PGL Setup 94
- Emulation Setup 97
- PGL Setup Submenus 98
- Auto Uppercase 99
- Select SFCC 99
- Host Form Length 99
- Power on IGP/PGL 101
- Ext Execute Copy 101
- AI 00 Spaces 101
- Select SO Char 101
- Ignore Mode 101
- UPC Descenders 103
- I-2/5 Selection 103
- C39 Compatbl 103
- PGL Normal 103
- • Disk = PCB Flash 105
- PRINTER SETUP Menu 106
- PRINTER SETUP Submenus 108
- Del Set from RAM 111
- Ld Set at PwrUp 111
- Main FFS 111
- Optimize&Reboot 112
- Print File List 112
- Auto Locking 112
- Set Lock Key 112
- Max Font Buffer 113
- Max Cache Memory 113
- Max Cached Char 113
- Standard Chars 114
- Bold Chars 114
- Extra Bold Char 114
- OCR-A Chars 114
- OCR-B Chars 114
- Tall Characters 115
- Batch Counter 115
- Feed Key Online 115
- Disp. Intensity 115
- Bot Line Display 116
- Admin User 116
- INTERFACES Menu 117
- Chapter 4 INTERFACES Menu 118
- Host Interface 121
- ETHERNET PORT 121
- ETHERNET SETTING 121
- WLAN SETTING 124
- Parallel Port 129
- Centronics 131
- IEEE 1284 132
- USB Port 132
- Serial Port 133
- • Printer Status 137
- • ENQ/STX (see Table 11) 137
- • ENQ (see Table 12) 137
- Printer Mgmt 138
- CONFIGURATION MENU 141
- CONFIGURATION Submenus 142
- Reset Cfg Names 143
- Auto Save 143
- DIAGNOSTICS Menu 144
- Printer Tests 145
- Test Count 145
- PrintHead Usage 147
- Head On Time 147
- Reset Head Data 147
- Head Resolution 147
- Head Voltage 147
- Saving a Configuration 148
- Auto Save Functionality 149
- Auto Save Feature 149
- Printing a Configuration 154
- Method 1 155
- Method 2 155
- Loading a Saved Configuration 156
- 5 Downloading Software 157
- ↵ and keys 158
- IMPORTANT 159
- Corrupt Code 166
- Using TrueType Fonts 167
- Downloading TrueType Fonts 167
- Adding A Header 168
- ↵ + keys 169
- ↵ (Enter), and (Cancel) 169
- Main FFSView File List or 170
- PTX_SETUP 171
- Labeling Applications 171
- To Print ASCII Characters 172
- To Print All Characters 172
- Main FFSFlash Avail 173
- EMC FFSFlash Avail 173
- 6 Routine Care and 175
- Printhead Cleaning 176
- Platen Roller Cleaning 177
- Media Sensor Cleaning 177
- Chapter 6 Cleaning 178
- Cutter Option Cleaning 179
- Media Damper Cleaning 179
- Handshaking 181
- Controlling Print Quality 182
- Determining Printhead Wear 182
- Replacing the Printhead 183
- • Label(s) did not get 189
- • A portion of the printed 189
- • Print quality is good, but 194
- • An occasional blank label 194
- Printer Alarms 195
- Fault Messages 195
- ↵ (Enter) and 213
- Status Messages 215
- A Specifications 219
- Appendix A 220
- Figure 5. Media Dimensions 221
- SL4M/T4M 221
- Media Thickness 222
- Media Capacity 222
- Media Cutter Option 223
- Host Interfaces 224
- Environmental 225
- Physical 225
- Acoustic Noise 225
- B Printer Options 227
- Real Time Clock 228
- Network Interface Card (NIC) 229
- DBCS Character Sets and Fonts 229
- Appendix B Software Options 230
- Installing the QCMC 231
- Exceptions 237
- Installing the EMC 238
- Configure The Printer Menu 240
- Load Media 241
- Deck Lock Lever 242
- Standard 242
- Peel Door 242
- Configure the Printer Menu 243
- Rewinder Full Sensor Setup 246
- Adapters 247
- Media Rewinder Clip 255
- Rewinder 255
- Supplies 258
- Genuine Printronix Media 259
- Ribbon and Media Usage 260
- C ASCII Control Codes 261
- Appendix C 262
- D PTX_SETUP Commands 263
- General Commands 264
- Summary of the CONFIG Command 269
- Thermal Commands 271
- E Customer Support 273
- Corporate Offices 274
- F Glossary 275
- Appendix F 276
- G Communication Notices 281
- Appendix G Notices 282
- Communication Notices 283
- CE Notice (European Union) 284
- 海拔高度和非热带性气候声明 285
- Wireless Ethernet 286
- OpenSSL License 289
- Original SSLeay License 290
- OpenSSL: 291
- WPA Supplicant License 291
- Numerics 295
- *251674-001* 308
Relacionado con productos y manuales para Impresión y escaneo Printronix SL4M MP2
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales